-
1 диаметр основной окружности
Русско-английский автомобильный словарь > диаметр основной окружности
-
2 диаметр основной окружности
Универсальный русско-английский словарь > диаметр основной окружности
-
3 основной диаметр
1) Oil: base diameter -
4 основная окружность
1) Engineering: base circle, base circle (зубчатого зацепления), generating circle2) Automobile industry: generating circle (зубчатого колеса), rolling circle (шестерни), ground circle (зубчатого колеса)3) Automation: base (diameter) circle, construction circle, generating circle (ЗК), rolling circle (ЗК)4) Makarov: base circle (в зубчатых зацеплениях), generating circle (в зубчатых зацеплениях)Универсальный русско-английский словарь > основная окружность
-
5 радиус
radius
- виража — radius of turn
- выхода из пикирования — pull-out radius
- действия (ла) — radius of action
половина расчетной дальности полета при безветрии. — half the range in still air.
- закругления углов (проема аварийного выхода) — corner radius
данный аварийный выход имеет прямоугольный проем с радиусами закругления углов не более 1/3 ширины выхода. — this emergency exit has а rectangular opening with corner radius not greater than 1/3 the width of the exit.
- земли, экваториальный — earth equatorial radius
- изгиба — bend radius
при установке трубопроводов следить, чтобы величина радиуса изгиба трубы была не менее пяти диаметров данной трубы. — when installing the tubing, allow bend radius of at least five times the tube diameter.
- крейсерского полета — cruising radius
дальность полета без последующей заправки при 25 % остатке топлива. — the distance an aircraft can travel before it necessary to refuel with a remaining or reserve fuel supply of 25 % of total fuel capacity.
- круга (разворота при рулении) — turning radius
- лопасти (возд. винта) — (propeller) blade radius
- несущего винта — (main) rotor radius
расстояние от конца лопасти до центра втулки при нулевом угле отклонения лопасти относительно вертикального шарнира и нулевом угле взмаха (свеса). — rotor radius is а distance of the blade tip from the rotor hub centre for zero lag angle and zero or built-in coning angle.
- поворота колеса — wheel turning radius
радиус круга, длина окружности которого равна пути, проходимому вперед колесом за один оборот. — radius of а circle whose circumference is equal to the distance moved forward by the wheel during a single revolution.
- полета — radius of action
максимальная дальность полета ла, обеспечивающая возвращение на свою базу (аэродром вылета) с остатком топлива порядка 25 % от полной заправки. — the maximum distance which an aircraft can fly and return to the base with a reserve fuel supply of 25 % of total fuel capacity.
- полета (с возвращением на свою базу, базу вылета) — radius of action (returning to the same base)
- полета (с возвращением на другую базу) — radius of action (returning to а different base)
- разворота — radius of turn
- разворота (при рулении) no внешним (наружным) колесам основной-опоры шасси, минимальный — minimum turning radius of main wheel (r2)
- разворота (при рулении) по внутренним колесам основной опоры шасси, минимальный — minimum turning radius (r1)
- разворота (при рулении) по наружной законцовке крыла, минимальный — minimum turning radius to clear wing tip (r4)
- разворота (при рулении) по переднему колесу, минимальный — minimum turning radius of nose wheel (r3)
- разворота самолета на земле, минимальный (по оси стойки шасси основной опоры, в сторону которой производится разворот) — minimum turning radius of inner main landing gear, minimum turning radius
-, тактический (полета) — radius of action
- угла проема (двери люка) — door opening corner radius
- штопора — radius of spin
на p. — at the radius
сечение лопасти на 1/3 радиуса. — blade cross section at 1/3 radius.
трещины в р. — cracks in radius
запиливать острую кромку no радиусу (5 мм) — file sharp edge to radius (of 5 mm)Русско-английский сборник авиационно-технических терминов > радиус
См. также в других словарях:
Base diameter — In mechanical engineering, the base diameter of an involute gear is the diameter of the base circle.1 Notes 1. ANSI/AGMA 1012 G05 , Gear Nomenclature, Definition of Terms with Symbols … Wikipedia
circle — See base circle bolt hole circle cam heel hole circle pitch circle diameter pitch circle traffic circle turning circle wheel bolt hole circle … Dictionary of automotive terms
Form diameter — is the diameter of a circle at which the trochoid (fillet curve) produced by the tooling intersects, or joins, the involute or specified profile. Although these terms are not preferred, it is also known as the true involute form diameter (TIF),… … Wikipedia
Circle — This article is about the shape and mathematical concept. For other uses, see Circle (disambiguation). Circle illustration showing a radius, a diameter, the centre and the circumference … Wikipedia
Circle of confusion — For the closely related topic in microscopy, see Point spread function. In optics, a circle of confusion is an optical spot caused by a cone of light rays from a lens not coming to a perfect focus when imaging a point source. It is also known as… … Wikipedia
Great circle — For fictional interstellar organization called Great Circle, see Andromeda (novel). A great circle divides the sphere in two equal hemispheres A great circle, also known as a Riemannian circle, of a sphere is the intersection of the sphere and a… … Wikipedia
Miami Circle — This article is about the architectural site in Miami, Florida. For design district in Atlanta, Georgia, see Lindbergh/Morosgo. The Miami Circle at Brickell Point Site U.S. National Register of Historic Places … Wikipedia
Sheldon Stone Circle — is a prehistoric stone circle, located at grid reference gbmappingsmall|NJ822249, to the south east of Oldmeldrum, Aberdeenshire, Scotland. Description Sheldon, sitting like a crown on a ridge may not be a recumbent stone circle as no recumbent… … Wikipedia
List of gear nomenclature — Gears have a wide range of unique terminology known as gear nomenclature. Many of the terms defined cite the same reference work.[1] Contents 1 Addendum 2 Addendum angle 3 Addendum circle … Wikipedia
Gear — For the gear like device used to drive a roller chain, see Sprocket. This article is about mechanical gears. For other uses, see Gear (disambiguation). Two meshing gears transmitting rotational motion. Note that the smaller gear is rotating… … Wikipedia
Tube socket — Left to right: octal (top and bottom view), loctal, and miniature (top and side view) sockets. An early transistor socket and an IC socket are included for comparison. Tube sockets are electrical sockets into which vacuum tubes (also known as… … Wikipedia